Seam drum
Cause: Water in the surface of the floor: During the installation process, it is inevitable that the glue does not completely fill the seam. If the mop drip when mopping the floor will cause water on the surface of the floor and enter from the seam with less sizing, the floor substrate will absorb moisture, causing local expansion and blistering. This is the case where the seam on the surface of the floor is partially bulged.
Under the floor, the water enters the drum: the surface phenomenon is that the joints are more uniform in shape, the places near the water source are heavier, and the far places are more and more flat. Somewhere with such problems are: close to the bathroom, kitchen, heating pipes, air conditioning condensate drains, windows, etc. If the water immersion time is long and the surface phenomenon is not obvious, you can open the floor to check if there is a watermark to determine the cause.
Short seams on the floor: Drums: Each short-edge seam is a drum, usually caused by too much moisture on the ground. The higher the bulge, the greater the tidal moisture on the ground.
Maintenance plan: Replace the floor.
Floor arching
Reason: The expansion joint is not reserved enough to make the floor arch.
Room-wide shop: Two or more rooms are not equipped with buckles when installing the floor. When the moisture and moisture are large, the two rooms floor are stretched laterally, causing the door to be involved at each other to make the floor arch.
The expansion joint is nailed by the baseboard or filled with plaster, putty, etc., so that the floor cannot be stretched, causing the floor to arch.
During the installation process, foreign matter remains under the floor, causing arching.
The base layer under the floor is arched. For example, the original floor has solid wood floor before the floor is installed. After the floor is installed, the original floor is damp and arched, causing the floor to be arched.
Maintenance plan: start the skirting board, reserve the expansion joint again; install the buckle at the connection between the room and the room; re-install the baseboard, clean out the expansion joints such as plaster and putty; open the floor and refill; The floor is dropped, the floor is leveled, and the floor is re-paved after drying.
Floor crack
Reason: The ground is not flat: the floor is paved in the case of uneven ground. After a period of use, the glue between the floors is separated to create a gap.
Less glue: the floor is in the winter, there is heating and baking, the air is dry, the floor is flat, the joint glue is insufficient, the strength is not enough, and the floor is opened and the seam is cracked.
There are heavy objects on the opposite side: the parallel opposite direction of the floor to be repaired is pressed by heavy objects, so that the floor cannot be freely contracted and cracks occur; such a room will be arched in the summer, and cracks will occur in the winter when the heating comes.
Maintenance plan: remove the floor, the floor is leveled, dry and re-paved; according to the size of the crack, decide to add wax, refill; use special tools to fix or reload; remove heavy objects, refill and fix.
Surface defects
Reason: Falling angle: The floor bumps during the handling process. The construction personnel did not pay attention to it during the construction process or shoveled the glue when cleaning the glue after the construction, so that the corners of the floor were dropped.
Surface shedding: After the construction, the sharp objects or heavy objects fall off the floor and the floor is affected; or the surface layer and the substrate are not glued during the processing of the floor. After a period of use, the surface layer and the substrate are degummed.
Scratches: When the customer puts furniture or heavy objects on the floor, the floor and the items are mixed with nails or sand, etc., and dragging on the floor causes the wear layer of the floor to be damaged or obvious scratches.
Maintenance plan: wax block repair or replacement of the floor.
Basic principles of furniture layout
Ensure that the activities in the room are unconstrained and that all furniture is in order.
Rethink the route of the event space. Your activity channel requires a minimum of 60cm, so that the main activity channel does not interfere with the placement of the main furniture in the room.
The sofa in the living room, the bed in the bedroom, and the desk in the office all need to occupy most of the available space, so first consider the placement of such furniture.
The distance between the coffee table and the sofa can be between 35cm and 45cm.
When the living room is arranged, the furniture and furniture should be kept within 240cm, so that people can have a comfortable conversation when they sit down. Remember, if possible, try not to put furniture and furniture on top, preferably on the opposite side. You may also want to put a table next to your seat so that people have a place to eat and drink.
This category is for Highlighter Brush which is necessary for creating a flawlessly illuminated look. There are some different types of Highlighter Brushes with different shapes of brush head. Each brush features soft and full bristles to ensure a smooth and effortless application of highlighter or blush products. Some of them can also be used as Blush Brush, Bronzer Brush or Contour Brush.
Highlighter Brushes
Highlighter Brush,Tapered Highlighting Brush,Professional Highlighting Brush,Makeup Brush For Highlighter
SHENZHEN MERRYNICE COSMETICS CO., LTD , https://www.merrynice.com